Home  5  Books  5  GBEzine  5  News  5  HelpDesk  5  Register  5  GreenBuilding.co.uk
Not signed in (Sign In)

Categories



Green Building Bible, Fourth Edition
Green Building Bible, fourth edition (both books)
These two books are the perfect starting place to help you get to grips with one of the most vitally important aspects of our society - our homes and living environment.

PLEASE NOTE: A download link for Volume 1 will be sent to you by email and Volume 2 will be sent to you by post as a book.
Buy individually or both books together. Delivery is free!


powered by Surfing Waves




Vanilla 1.0.3 is a product of Lussumo. More Information: Documentation, Community Support.

Welcome to new Forum Visitors
 Join the forum now and benefit from discussions with thousands of other green building fans and discounts on Green Building Press publications: Apply now.




General: Ground floor slab/insulation.

Bottom of Page

1 to 22 of 22

  1.  
  1.  
    My agreed spec for the make up of the ground floor slab [ To a barn conversion] is as follows:-
    Mot type 1
    Dpm
    100mm conc
    50mm cellotex
    Wet UFH
    50-75mm screed
    Floor tiles

    My question is :-
    Any advantage in increasing the 50mm cellotex to 100mm thick?
    Thanks.
    :cool:
    • CommentAuthortony
    • CommentTimeOct 9th 2007
     
    No! But there may be a good case for not having it at all under most of the floor. Just arround the edges.

    If it were mine I would put it under the concrete.

    What kind of use will the barn have? Full time occupancy or intermittent?

    What is the thermal resistance of the whole floor -- soil MOT stuff, concrete , screed , tiles? Do you need any insulation?
    •  
      CommentAuthornigel
    • CommentTimeOct 10th 2007
     
    The thickness of insulation you need depends a lot on the ratio of floor area to perimeter.

    Personally I would go with 100mm esp if you are using UFH as you will never add it back later.

    This link should help http://www.insulateonline.com/index1.htm?floorsintro.htm~main

    I would agree that it would be better to have the thermal mass on the warm side of the insulation.
    • CommentAuthorTerry
    • CommentTimeOct 10th 2007
     
    Just wondering what the reason is for having the concrete layer?
    If you are going to insulate, ignoring Tony's comment for the moment on what is really required, why not replace the concrete and celotex with 150 eps?
    • CommentAuthortony
    • CommentTimeOct 10th 2007
     
    That would be cheaper if it was necessary but you should still have a structural floor somewhere.
    • CommentAuthorJohan
    • CommentTimeOct 11th 2007
     
    300mm of foamed glass or LWA nder the con/limecrete slab will do the trick.
    • CommentAuthorBluemoon
    • CommentTimeOct 11th 2007
     
    How about fluffy concrete, sort of similar to Celcon Solar wall blocks?
  8.  
    Thanks for all your help, i have decided that Tony has the solution, which has been confirmed by 'Kingspan' tech dept.
    50mm Kingspan/Cellotex with an increase around the perimeter [greatest heat loss] - 100mm.
    Thanks again.
  9.  
    I thought Celotex / Kingspan couldn't go under a slab, or am I misunderstanding the thread?

    J
  10.  
    James, I have seen PUR used both above and below the concrete slab, though I prefer below.
  11.  
    I was thinking rather what Celotex / Kingspan and their BBA certs preferred...

    J
  12.  
    It does not matter, either is acceptable, provided you follow their details [Detail sheet 2, figs 1&3]
    http://www.bbacerts.co.uk/certs/31/3197i2_web.pdf
    • CommentAuthortony
    • CommentTimeOct 14th 2007
     
    Couple of points 1) I can never see why there is need for both vapour control on warm side and dpm on the cold side. All I have ever done is thick polythene on top as combined dpm/vapour control.

    2) concrete and screed both react with aluminium so any spills seeps etc will naff the foil layer.
  14.  
    I agree with 1, but I follow their spec as I am not sure that PUR is totally impermiable. I have heard that it is not and the BBA spec seems to back this up.

    Re point 2 are you sure it is Aluminium?
    • CommentAuthortony
    • CommentTimeOct 14th 2007
     
    Not sure that it is ali but it sure looses its shine on contact with cement.
  16.  
    Yes it does, perhaps that is why they recomend a barrier? I think it is something shiny, but not Aluminium - no proof however
  17.  
    <blockquote><cite>Posted By: Mike George</cite>It does not matter, either is acceptable, provided you follow their details [Detail sheet 2, figs 1&3]</blockquote>

    Mike,

    ...well you learn something new every day, to be honest the last time I asked them it was on a commercial project w/ 5kn/m2 live floor load, perhaps it was that that scared them off.

    So under slab to provide more thermal mass (I assume) but EPS or PU...?

    J
  18.  
    Doh , should've used html mode.
  19.  
    A matter of choice dependent [for me] on the need for building up height to finish floor level.You need less PUR but EPS is nicer to use. Details here: http://www.bbacerts.co.uk/certs/17/1796i6_web.pdf
    • CommentAuthorbayouboy
    • CommentTimeOct 16th 2007
     
    The main thing to remember with underfloor heating is that the temperature difference between inside and outside is much greater than with indoor air temperature. Secondly, you are dealing with liquids and solids, so heat transfer is greater than air-solid-air ( as in a wall. Although the earth below the slab is more or less constant in temperature in the centre, and is not very cold, the heating pipes will be between 40C and 60C depending on the systems, rather than 20C. Your heat will flow continuously into the ground without good levels of insulation. I would go towards Johan's 300mm of foamed glass.
    • CommentAuthorBluemoon
    • CommentTimeOct 16th 2007
     
    I am at the start of removing the screed in my ground floor bathroom. Base is about 100mm thick, there is a thick polythene film then the screed about 80mm thick. The room is 3M square. one outside wall with window. As I am laying ceramic tiles on the new screed, I want to install an electric heating mat to take the chill off the floor. I realise I won't meet the latest standards for insulation, but will about 20mm of board make any real difference? I have installed pipes for a rad, and can fit one one if needed. There is also a 800watt towel rail in the system.
    • CommentAuthortony
    • CommentTimeOct 16th 2007
     
    How about running some pipes in the screed -- a big loop in parallel with the rad and an adjusting valve near the rad? or just extend the radiator pipes under the floor for a bit.

1 to 22 of 22

  1.  
Add your comments

    Username Password
  • Format comments as
 
Back to Discussions Top of Page
   
The Ecobuilding Buzz
Site Map    |   Home    |   View Cart    |   Pressroom   |   Business   |   Links   
Logout    

© Green Building Press